You are here:   Products > Control > Solid State Relays Power Controllers
Register   |  Login

Contact Details: +353 87 2768099 | +353 45 831575 | info@wpa.ie

Minimize

RP7 - LUMEL 1 Phase Power Controller

The LUMEL RP7 power controller allows control and delivery of power from an a.c. voltage source to a resistive or resistance-inductive receiver of electrical energy. e.g. rotational speed of 1-phase induction motors with a capacitor or commutator motors with small loads.

Designed for use in control systems with a continuous output.  

Input: 0...5 V, 0...10 V, 0...20 mA, 4...20 mA, Potentiometer
Control function: ON/OFF, pulse, time-lag release “soft-start”
Output current: 5 A, 10 A, 15 A
Mounting: DIN rail
Isolation: Galvanic
Dimensions: 41 x 93 x 105mm
RP7 - LUMEL 1 Phase Power Controller  
Data Sheet
RP7 - 1 Phase Power Controller  datasheets
  
Manual
RP7 - 1 Phase Power Controller  manuals

RP1 - 1 Phase Power Controller

The RP1 power controller is designed for automatic temperature control in electro-thermal systems.
It can be applied in electric circuits with resistive or inductive loads and resistance loads with a high temperature resistance coefficient.

The RP1 single phase power controller is a contact-less power control device which includes a thyristor connector and electronic gate trigger system (GTS). The RP1 controls the power delivered to the electric energy load via analog or pulse control signal. Two or three power controllers can be applied in 3-phase systems.

Additional functions: load current limitation, trigger deceleration of soft-start, control of the initial trigger angle value, control of the input line amplification, trigger stoppage by an external signal, supervising and signalling of current in the load circuit, output U = f(Io), supervising of the radiator temperature, overload signalling, signalling of the fuse damage, Output of „Master/Slave” type, relay outputs.

Control Function: On/Off control, Pulse control fast cycle - slow cycle, Phase control
Input: 0 .. 10 kOhm, impulse 0/4 .. 32 V, 0 .. 5 V ,0 .. 10 V, 0 .. 20 mA, 4 .. 20 mA
Output current: 25A, 40A, 70A, 125A
Mounting: Wall
Isolation: Galvanic
Dimensions: 135 x 231 x 199mm
1-phase power controller - RP1
Data Sheet
  
Manual

RP6 - 1 Phase Solid State Relay

The RP6 solid state relay allows control and delivery of power from an a.c. voltage source to a resistive or resistance-inductive receiver of electrical energy. Designed to be used in control systems, to co-operate with controllers with a discontinuous or continuous output.

Control Function: ON/OFF, pulse
Input:0 .. 5 V, 0 .. 10 V, 0 .. 20 mA, 4 .. 20 mA, 0 .. 10 K ohm, pulse 0/4...28V
Output current: 5 A, 10 A, 15 A
Mounting: DIN rail
Isolation: Galvanic
Dimensions: 50 x 93 x 105mm
1-phase solid state relay RP6
Data Sheet
1-phase solid state relay RP6 datasheets
 


RP3 - 3 phase power controllers

The RP3 power controller is a contactless three-phase power controller which includes a thyristor connector and an electronic gate triggering system (GTS). This power controller allows the control of the power delivered from a three-phase voltage source to an electrical energy load in conjunction with an input control signal. The RP3 power controller is designed for three-phase resistive, resistive-inductive loads which require control.

The application area of RP3 power controllers are:
Electrical furnaces, drying construction, belt- type furnaces, annealing furnaces, hard soldering, crucible furnaces, smelters,  salt bath hardening furnaces, extruding presses for plastics, tempering , spot/seam welding , glass, glazing, infrared-ultraviolet radiation  drying , glass melt, pre heating and glass forming.

Additional Functions
Load current limitation, soft start delay, Control of the initial gating angle value, Control of the input line amplification, Supervising and signaling of the current in the load circuit, output U= f(lo),Supervising of the radiator temperature, Signalling of the fuse damage, Signalling of the incorrect phase sequence, Signalling of overload and Relay outputs.


Control Function: On-off, fast cycle - fi max » 1 Hz, slow cycle- fi max » 0.1 Hz, Phase control.
Input: 0 .. 10 k Ohm, impulse 0/4 .. 32 V, 0 .. 5 V, 0 .. 10 V, 0 .. 20 mA, 4 .. 20 mA
Output current: 450 A
Mounting: Wall
Isolation: Galvanic
Dimensions: See data sheet
RP3 three - phase power controller
Data Sheet
RP3 three - phase power controller datasheets
  
Manual
RP3 three - phase power controller manuals

Control Function
On-off control,Chopper control: fast cycle - fi,max » 1 Hz, slow cycle - fi,max » 0.1 Hz.,Phase control